Leprecon LP-3000 Series Manuel d'utilisateur Page 31
- Page / 186
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
LP-3000 Users Manual
Chapter Three:
System Tools
The LP-3000’s system tools include features that enable you to configure the
console for a specific lighting system and to load, save and erase shows. The
system tools are available from the Setup screen and the following functions are
available.
Menu Item Function
Show Used to save and load LP-3000 show files.
Preset Titles Sets the LCD titles above the preset playbacks.
DMX Lines Assigns dimmers and moving lights to 1 of 4 lines.
Dimmer Patch Assigns dimmers to board channels.
Options Used to set preferences, including bump levels.
Erase Clears stored show data.
DMX Line Assignment
Before controlling fixtures with the LP-3000, you must first configure the system
with the correct number and type of fixtures. This configuration process will
determine the DMX assignments for moving lights and dimmers and allow you to
give names to the fixtures for easier reference during programming.
About DMX Line Assignments
DMX line assignment locates a fixture on a specific DMX line at a specific DMX
address.
A fixture assignment consists of a DMX line and a start address.
• Up to four DMX lines can be driven from the LP-3000. The four DMX lines
are Line A, Line B, Line C and Line D.
• Each DMX line has 512 channels, any one of which may be used as the
start address for a fixture.
Various fixtures require different numbers of channels. For example, the Martin 218
requires nine channels whereas the Cyberlight requires twenty channels. The
number of attributes that a fixture has determines the number of channels it
requires.
- LP-3000 Users Manual 1
- Version 330 3
- Contents 5
- Introduction 11
- LP-3000 Features 12
- Section One: 13
- Getting Started 13
- Chapter One: 15
- Manual Console Operation 15
- To Power Down the LP-3000 16
- LP-3000 Master Panel 18
- X and Y Manual Scene Faders 18
- (Y position.) 21
- Chapter Two: 23
- LP-3000 Show Basics 23
- The Stage View Screen 24
- To View the Show Screen 25
- To Create a New Show 26
- To Open an Existing Show 27
- To Close a Show 27
- To Copy a Show 27
- To Backup a Show 28
- To Load a Show from a Disk 28
- To Format a Floppy Disk 28
- System Tools 31
- Chapter Three: 31
- 28 Chapter Three System Tools 32
- System Tools Chapter Three 29 33
- 30 Chapter Three System Tools 34
- System Tools Chapter Three 31 35
- 32 Chapter Three System Tools 36
- To Edit a Fixture 37
- To Delete a Fixture 38
- To View Unused Assignments 38
- To View Fixture Information 39
- Dimmer Patch 40
- To Select a Patch 41
- To Create a New Patch 42
- System Tools Chapter Three 39 43
- To Copy a Patch 44
- System Tools Chapter Three 41 45
- 42 Chapter Three System Tools 46
- Erasing Show Components 47
- 44 Chapter Three System Tools 48
- Button Function 48
- Section Two: 49
- Conventional Light Controller 49
- Chapter Four: 51
- Basic Preset Techniques 52
- To Play Back Presets 53
- To Preview Presets 53
- To Edit Presets with Faders 54
- Manual Fader Re-Capture 55
- Live and Blind Edits 55
- Entering Preset Titles 56
- Preset Scenes 57
- To Edit Presets 58
- Presets Chapter Four 55 59
- Chapter Five: 61
- To Play Back a Chase 62
- To Set the Chase Rate 63
- To Store the Chase Rate 63
- Run Controls 63
- 60 Chapter Five Chases 64
- To Edit a Chase on a Playback 65
- To Create a New Chase 65
- 62 Chapter Five Chases 66
- Chases Chapter Five 63 67
- 64 Chapter Five Chases 68
- Chases Chapter Five 65 69
- Editing Chases 70
- To Shorten a Chase 71
- To Delete a Step 71
- To Delete a Chase 71
- Chapter Six: 73
- Cue Stacks 73
- Adding Cues to a Stack 74
- To Set Fade Times 75
- 72 Chapter Six Cue Stacks 76
- Cue Stacks Chapter Six 73 77
- Playing Back Cue Stacks 78
- Cue Stacks Chapter Six 75 79
- Editing Stacks 80
- To Delete a Stack 81
- Section Three: 83
- Moving Light Controller 83
- Chapter Seven: 85
- No Change 87
- Panel Layout 88
- Chapter Eight: 89
- Moving Light Cue Programming 89
- Selecting Fixtures 90
- Instrument Groups 92
- Live Mode versus Blind Mode 93
- Setting Cue Properties 93
- Save As Cue 96
- Saving the Cue to a Playback 97
- To Check the Cue 98
- Chapter Nine: 99
- Moving Light Cue Playback 99
- Viewing the Playback Status 100
- Changing Cue Order 101
- Overriding a Look 104
- Chapter Ten: 107
- Editing Moving Light Cues 109
- To Add a New Cue to a Show 110
- To Delete a Cue from a Show 110
- To Edit a Cue 111
- To Rename a Cue 111
- To Program a New Cue 112
- To Create a Cuelist 112
- Chapter Eleven: 119
- Attribute Programming 119
- Chapter Twelve: 123
- Creating New Labels 123
- To Create a Focus Label 128
- Editing Labels 130
- To Edit a Label 131
- To Rename a Label 131
- To Delete a Label 132
- Appendices 135
- Appendix A: 137
- Maintenance and Repair 137
- Appendix B: 139
- Instrument Library Version 29 139
- Golden Scan 3 140
- Golden Scan HPE 140
- MiniScan HPE 140
- Stage Color 300 140
- Stage Color 1200 141
- Stage Light 300 141
- Stage Zoom 141
- CF 1200 Hard Edge 142
- CF 1200 Wash 142
- Nat MM 1200 + 2500 143
- Color Changer 143
- High End Systems 144
- Cyberlight CX Mode 3 145
- Cyberlight Mode 2 145
- Cyber Litho Mode 2 146
- IntellaBeam 8 Channel 146
- I-Beam 8 ch. Hi res 147
- IntellaBeam 13 chan 147
- Studio Color 147
- Studio Color 250 148
- Studio Spot 148
- Studio Spot 250 149
- Technobeam 149
- Lamp Lite 150
- 1220 CMYR 151
- 1220 RPR 152
- 218 Mkll 153
- PAL1200E 156
- Robocolor Pro 400 156
- Pan Command 157
- Studio Due 157
- Vari*light 158
- Forerunner 159
- Appendix C: 161
- Attribute Labels 167
- Appendix D: 169
- Control Features 169
- Appendix E: 173
- Importing a Device 174
- Glossary 177
- 174 Glossary 178
- Recorded 179
- Channel Value 179
- Preset Playback 179
- Position 179
- 176 Glossary 180
- Glossary 177 181
- 180 Index 184
- Index 181 185
- 182 Index 186
© 2020, manymanuals.fr. Tous droits réservés | 0.138 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels